AMiRo-OS

/*! ------------------------------------------------------------------------------------------------------------------

 * @file    deca_regs.h

 * @brief   DW1000 Register Definitions

 *          This file supports assembler and C development for DW1000 enabled devices

 *

 * @attention

 *

 * Copyright 2013 (c) Decawave Ltd, Dublin, Ireland.

 *

 * All rights reserved.

 *

 */

#ifndef DECA_REGS_H

#define DECA_REGS_H

#ifdef __cplusplus

extern "C" {

#endif

#include <amiro-lld.h>

/****************************************************************************//**

 * @brief Bit definitions for register DEV_ID

**/

#define DEV_ID_ID               0x00            /* Device ID register, includes revision info (0xDECA0130) */

#define DEV_ID_LEN              (4)

/* mask and shift */

#define DEV_ID_REV_MASK         0x0000000FUL    /* Revision */

#define DEV_ID_VER_MASK         0x000000F0UL    /* Version */

#define DEV_ID_MODEL_MASK       0x0000FF00UL    /* The MODEL identifies the device. The DW1000 is device type 0x01 */

#define DEV_ID_RIDTAG_MASK      0xFFFF0000UL    /* Register Identification Tag 0XDECA */

/****************************************************************************//**

 * @brief Bit definitions for register EUI_64

**/

#define EUI_64_ID               0x01            /* IEEE Extended Unique Identifier (63:0) */

#define EUI_64_OFFSET           0x00

#define EUI_64_LEN              (8)

/****************************************************************************//**

 * @brief Bit definitions for register PANADR

**/

#define PANADR_ID               0x03            /* PAN ID (31:16) and Short Address (15:0) */

#define PANADR_LEN              (4)

/*mask and shift */

#define PANADR_SHORT_ADDR_OFFSET 0              /* In bytes */

#define PANADR_SHORT_ADDR_MASK  0x0000FFFFUL    /* Short Address */

#define PANADR_PAN_ID_OFFSET     2              /* In bytes */

#define PANADR_PAN_ID_MASK      0xFFFF00F0UL    /* PAN Identifier */

/****************************************************************************//**

 * @brief Bit definitions for register 0x05

**/

#define REG_05_ID_RESERVED      0x05

/****************************************************************************//**

 * @brief Bit definitions for register SYS_CFG

**/

#define SYS_CFG_ID              0x04            /* System Configuration (31:0) */

#define SYS_CFG_LEN             (4)

/*mask and shift */

#define SYS_CFG_MASK            0xF047FFFFUL    /* access mask to SYS_CFG_ID */

#define SYS_CFG_FF_ALL_EN       0x000001FEUL    /* Frame filtering options all frames allowed */

/*offset 0 */

#define SYS_CFG_FFE             0x00000001UL    /* Frame Filtering Enable. This bit enables the frame filtering functionality */

#define SYS_CFG_FFBC            0x00000002UL    /* Frame Filtering Behave as a Co-ordinator */

#define SYS_CFG_FFAB            0x00000004UL    /* Frame Filtering Allow Beacon frame reception */

#define SYS_CFG_FFAD            0x00000008UL    /* Frame Filtering Allow Data frame reception */

#define SYS_CFG_FFAA            0x00000010UL    /* Frame Filtering Allow Acknowledgment frame reception */

#define SYS_CFG_FFAM            0x00000020UL    /* Frame Filtering Allow MAC command frame reception */

#define SYS_CFG_FFAR            0x00000040UL    /* Frame Filtering Allow Reserved frame types */

#define SYS_CFG_FFA4            0x00000080UL    /* Frame Filtering Allow frames with frame type field of 4, (binary 100) */

/*offset 8 */

#define SYS_CFG_FFA5            0x00000100UL    /* Frame Filtering Allow frames with frame type field of 5, (binary 101) */

#define SYS_CFG_HIRQ_POL        0x00000200UL    /* Host interrupt polarity */

#define SYS_CFG_SPI_EDGE        0x00000400UL    /* SPI data launch edge */

#define SYS_CFG_DIS_FCE         0x00000800UL    /* Disable frame check error handling */

#define SYS_CFG_DIS_DRXB        0x00001000UL    /* Disable Double RX Buffer */

#define SYS_CFG_DIS_PHE         0x00002000UL    /* Disable receiver abort on PHR error */

#define SYS_CFG_DIS_RSDE        0x00004000UL    /* Disable Receiver Abort on RSD error */

#define SYS_CFG_FCS_INIT2F      0x00008000UL    /* initial seed value for the FCS generation and checking function */

/*offset 16 */

#define SYS_CFG_PHR_MODE_SHFT   16

#define SYS_CFG_PHR_MODE_00     0x00000000UL    /* Standard Frame mode */

#define SYS_CFG_PHR_MODE_11     0x00030000UL    /* Long Frames mode */

#define SYS_CFG_DIS_STXP        0x00040000UL    /* Disable Smart TX Power control */

#define SYS_CFG_RXM110K         0x00400000UL    /* Receiver Mode 110 kbps data rate */

/*offset 24 */

#define SYS_CFG_RXWTOE          0x10000000UL    /* Receive Wait Timeout Enable. */

#define SYS_CFG_RXAUTR          0x20000000UL    /* Receiver Auto-Re-enable. This bit is used to cause the receiver to re-enable automatically */

#define SYS_CFG_AUTOACK         0x40000000UL    /* Automatic Acknowledgement Enable */

#define SYS_CFG_AACKPEND        0x80000000UL    /* Automatic Acknowledgement Pending bit control */

/****************************************************************************//**

 * @brief Bit definitions for register SYS_TIME

**/

#define SYS_TIME_ID             0x06            /* System Time Counter (40-bit) */

#define SYS_TIME_OFFSET         0x00

#define SYS_TIME_LEN            (5)             /* Note 40 bit register */

/****************************************************************************//**

 * @brief Bit definitions for register  0x07

**/

#define REG_07_ID_RESERVED      0x07

/****************************************************************************//**

 * @brief Bit definitions for register TX_FCTRL

**/

#define TX_FCTRL_ID             0x08            /* Transmit Frame Control */

#define TX_FCTRL_LEN            (5)             /* Note 40 bit register */

/*masks (low 32 bit) */

#define TX_FCTRL_TFLEN_MASK     0x0000007FUL    /* bit mask to access Transmit Frame Length */

#define TX_FCTRL_TFLE_MASK      0x00000380UL    /* bit mask to access Transmit Frame Length Extension */

#define TX_FCTRL_FLE_MASK       0x000003FFUL    /* bit mask to access Frame Length field */

#define TX_FCTRL_TXBR_MASK      0x00006000UL    /* bit mask to access Transmit Bit Rate */

#define TX_FCTRL_TXPRF_MASK     0x00030000UL    /* bit mask to access Transmit Pulse Repetition Frequency */

#define TX_FCTRL_TXPSR_MASK     0x000C0000UL    /* bit mask to access Transmit Preamble Symbol Repetitions (PSR). */

#define TX_FCTRL_PE_MASK        0x00300000UL    /* bit mask to access Preamble Extension */

#define TX_FCTRL_TXPSR_PE_MASK  0x003C0000UL    /* bit mask to access Transmit Preamble Symbol Repetitions (PSR). */

#define TX_FCTRL_SAFE_MASK_32   0xFFFFE3FFUL    /* FSCTRL has fields which should always be writen zero */

/*offset 0 */

/*offset 8 */

#define TX_FCTRL_TXBR_110k      0x00000000UL    /* Transmit Bit Rate = 110k */

#define TX_FCTRL_TXBR_850k      0x00002000UL    /* Transmit Bit Rate = 850k */

#define TX_FCTRL_TXBR_6M        0x00004000UL    /* Transmit Bit Rate = 6.8M */

#define TX_FCTRL_TXBR_SHFT      (13)            /* shift to access Data Rate field */

#define TX_FCTRL_TR             0x00008000UL    /* Transmit Ranging enable */

#define TX_FCTRL_TR_SHFT        (15)            /* shift to access Ranging bit */

/*offset 16 */

#define TX_FCTRL_TXPRF_SHFT     (16)            /* shift to access Pulse Repetition Frequency field */

#define TX_FCTRL_TXPRF_4M       0x00000000UL    /* Transmit Pulse Repetition Frequency = 4 Mhz */

#define TX_FCTRL_TXPRF_16M      0x00010000UL    /* Transmit Pulse Repetition Frequency = 16 Mhz */

#define TX_FCTRL_TXPRF_64M      0x00020000UL    /* Transmit Pulse Repetition Frequency = 64 Mhz */

#define TX_FCTRL_TXPSR_SHFT     (18)            /* shift to access Preamble Symbol Repetitions field */

#define TX_FCTRL_PE_SHFT        (20)            /* shift to access Preamble length Extension to allow specification of non-standard values */

#define TX_FCTRL_TXPSR_PE_16    0x00000000UL    /* bit mask to access Preamble Extension = 16 */

#define TX_FCTRL_TXPSR_PE_64    0x00040000UL    /* bit mask to access Preamble Extension = 64 */

#define TX_FCTRL_TXPSR_PE_128   0x00140000UL    /* bit mask to access Preamble Extension = 128 */

#define TX_FCTRL_TXPSR_PE_256   0x00240000UL    /* bit mask to access Preamble Extension = 256 */

#define TX_FCTRL_TXPSR_PE_512   0x00340000UL    /* bit mask to access Preamble Extension = 512 */

#define TX_FCTRL_TXPSR_PE_1024  0x00080000UL    /* bit mask to access Preamble Extension = 1024 */

#define TX_FCTRL_TXPSR_PE_1536  0x00180000UL    /* bit mask to access Preamble Extension = 1536 */

#define TX_FCTRL_TXPSR_PE_2048  0x00280000UL    /* bit mask to access Preamble Extension = 2048 */

#define TX_FCTRL_TXPSR_PE_4096  0x000C0000UL    /* bit mask to access Preamble Extension = 4096 */

/*offset 22 */

#define TX_FCTRL_TXBOFFS_SHFT   (22)            /* Shift to access transmit buffer index offset */

#define TX_FCTRL_TXBOFFS_MASK   0xFFC00000UL    /* bit mask to access Transmit buffer index offset 10-bit field */

/*offset 32 */

#define TX_FCTRL_IFSDELAY_MASK  0xFF00000000ULL /* bit mask to access Inter-Frame Spacing field */

/****************************************************************************//**

 * @brief Bit definitions for register TX_BUFFER

**/

#define TX_BUFFER_ID            0x09            /* Transmit Data Buffer */

#define TX_BUFFER_LEN           (1024)

/****************************************************************************//**

 * @brief Bit definitions for register  DX_TIME

**/

#define DX_TIME_ID              0x0A            /* Delayed Send or Receive Time (40-bit) */

#define DX_TIME_LEN             (5)

/****************************************************************************//**

 * @brief Bit definitions for register 0x08

**/

#define REG_0B_ID_RESERVED      0x0B

/****************************************************************************//**

 * @brief Bit definitions for register RX_FWTO

**/

#define RX_FWTO_ID              0x0C            /* Receive Frame Wait Timeout Period */

#define RX_FWTO_OFFSET          0x00

#define RX_FWTO_LEN             (2)             /* doc bug*/

/*mask and shift */

#define RX_FWTO_MASK            0xFFFF

/****************************************************************************//**

 * @brief Bit definitions for register SYS_CTRL

**/

#define SYS_CTRL_ID             0x0D            /* System Control Register */

#define SYS_CTRL_OFFSET         0x00

#define SYS_CTRL_LEN            (4)

/*masks */

#define SYS_CTRL_MASK_32        0x010003CFUL    /* System Control Register access mask (all unused fields should always be writen as zero) */

/*offset 0 */

#define SYS_CTRL_SFCST          0x00000001UL    /* Suppress Auto-FCS Transmission (on this frame) */

#define SYS_CTRL_TXSTRT         0x00000002UL    /* Start Transmitting Now */

#define SYS_CTRL_TXDLYS         0x00000004UL    /* Transmitter Delayed Sending (initiates sending when SYS_TIME == TXD_TIME */

#define SYS_CTRL_CANSFCS        0x00000008UL    /* Cancel Suppression of auto-FCS transmission (on the current frame) */

#define SYS_CTRL_TRXOFF         0x00000040UL    /* Transceiver Off. Force Transciever OFF abort TX or RX immediately */

#define SYS_CTRL_WAIT4RESP      0x00000080UL    /* Wait for Response */

/*offset 8 */

#define SYS_CTRL_RXENAB         0x00000100UL    /* Enable Receiver Now */

#define SYS_CTRL_RXDLYE         0x00000200UL    /* Receiver Delayed Enable (Enables Receiver when SY_TIME[0x??] == RXD_TIME[0x??] CHECK comment*/

/*offset 16 */

/*offset 24 */

#define SYS_CTRL_HSRBTOGGLE     0x01000000UL    /* Host side receiver buffer pointer toggle - toggles 0/1 host side data set pointer */

#define SYS_CTRL_HRBT           (SYS_CTRL_HSRBTOGGLE)

#define SYS_CTRL_HRBT_OFFSET    (3)

/****************************************************************************//**

 * @brief Bit definitions for register  SYS_MASK

**/

#define SYS_MASK_ID             0x0E            /* System Event Mask Register */

#define SYS_MASK_LEN            (4)

/*masks */

#define SYS_MASK_MASK_32        0x3FF7FFFEUL    /* System Event Mask Register access mask (all unused fields should always be writen as zero) */

/*offset 0 */

#define SYS_MASK_MCPLOCK        0x00000002UL    /* Mask clock PLL lock event    */

#define SYS_MASK_MESYNCR        0x00000004UL    /* Mask clock PLL lock event    */

#define SYS_MASK_MAAT           0x00000008UL    /* Mask automatic acknowledge trigger event */

#define SYS_MASK_MTXFRB         0x00000010UL    /* Mask transmit frame begins event */

#define SYS_MASK_MTXPRS         0x00000020UL    /* Mask transmit preamble sent event    */

#define SYS_MASK_MTXPHS         0x00000040UL    /* Mask transmit PHY Header Sent event  */

#define SYS_MASK_MTXFRS         0x00000080UL    /* Mask transmit frame sent event   */

/*offset 8 */

#define SYS_MASK_MRXPRD         0x00000100UL    /* Mask receiver preamble detected event    */

#define SYS_MASK_MRXSFDD        0x00000200UL    /* Mask receiver SFD detected event */

#define SYS_MASK_MLDEDONE       0x00000400UL    /* Mask LDE processing done event   */

#define SYS_MASK_MRXPHD         0x00000800UL    /* Mask receiver PHY header detect event    */

#define SYS_MASK_MRXPHE         0x00001000UL    /* Mask receiver PHY header error event */

#define SYS_MASK_MRXDFR         0x00002000UL    /* Mask receiver data frame ready event */

#define SYS_MASK_MRXFCG         0x00004000UL    /* Mask receiver FCS good event */

#define SYS_MASK_MRXFCE         0x00008000UL    /* Mask receiver FCS error event    */

/*offset 16 */

#define SYS_MASK_MRXRFSL        0x00010000UL    /* Mask receiver Reed Solomon Frame Sync Loss event */

#define SYS_MASK_MRXRFTO        0x00020000UL    /* Mask Receive Frame Wait Timeout event    */

#define SYS_MASK_MLDEERR        0x00040000UL    /* Mask leading edge detection processing error event   */

#define SYS_MASK_MRXOVRR        0x00100000UL    /* Mask Receiver Overrun event  */

#define SYS_MASK_MRXPTO         0x00200000UL    /* Mask Preamble detection timeout event    */

#define SYS_MASK_MGPIOIRQ       0x00400000UL    /* Mask GPIO interrupt event    */

#define SYS_MASK_MSLP2INIT      0x00800000UL    /* Mask SLEEP to INIT event */

/*offset 24*/

#define SYS_MASK_MRFPLLLL       0x01000000UL    /* Mask RF PLL Loosing Lock warning event   */

#define SYS_MASK_MCPLLLL        0x02000000UL    /* Mask Clock PLL Loosing Lock warning event    */

#define SYS_MASK_MRXSFDTO       0x04000000UL    /* Mask Receive SFD timeout event   */

#define SYS_MASK_MHPDWARN       0x08000000UL    /* Mask Half Period Delay Warning event */

#define SYS_MASK_MTXBERR        0x10000000UL    /* Mask Transmit Buffer Error event */

#define SYS_MASK_MAFFREJ        0x20000000UL    /* Mask Automatic Frame Filtering rejection event   */

/****************************************************************************//**

 * @brief Bit definitions for register SYS_STATUS

**/

#define SYS_STATUS_ID           0x0F            /* System event Status Register */

#define SYS_STATUS_OFFSET       0x00

#define SYS_STATUS_LEN          (5)             /* Note 40 bit register */

/*masks */

#define SYS_STATUS_MASK_32      0xFFF7FFFFUL    /* System event Status Register access mask (all unused fields should always be writen as zero) */

/*offset 0 */

#define SYS_STATUS_IRQS         0x00000001UL    /* Interrupt Request Status READ ONLY */

#define SYS_STATUS_CPLOCK       0x00000002UL    /* Clock PLL Lock */

#define SYS_STATUS_ESYNCR       0x00000004UL    /* External Sync Clock Reset */

#define SYS_STATUS_AAT          0x00000008UL    /* Automatic Acknowledge Trigger */

#define SYS_STATUS_TXFRB        0x00000010UL    /* Transmit Frame Begins */

#define SYS_STATUS_TXPRS        0x00000020UL    /* Transmit Preamble Sent */

#define SYS_STATUS_TXPHS        0x00000040UL    /* Transmit PHY Header Sent */

#define SYS_STATUS_TXFRS        0x00000080UL    /* Transmit Frame Sent: This is set when the transmitter has completed the sending of a frame */

/*offset 8 */

#define SYS_STATUS_RXPRD        0x00000100UL    /* Receiver Preamble Detected status */

#define SYS_STATUS_RXSFDD       0x00000200UL    /* Receiver Start Frame Delimiter Detected. */

#define SYS_STATUS_LDEDONE      0x00000400UL    /* LDE processing done */

#define SYS_STATUS_RXPHD        0x00000800UL    /* Receiver PHY Header Detect */

#define SYS_STATUS_RXPHE        0x00001000UL    /* Receiver PHY Header Error */

#define SYS_STATUS_RXDFR        0x00002000UL    /* Receiver Data Frame Ready */

#define SYS_STATUS_RXFCG        0x00004000UL    /* Receiver FCS Good */

#define SYS_STATUS_RXFCE        0x00008000UL    /* Receiver FCS Error */

/*offset 16 */

#define SYS_STATUS_RXRFSL       0x00010000UL    /* Receiver Reed Solomon Frame Sync Loss */

#define SYS_STATUS_RXRFTO       0x00020000UL    /* Receive Frame Wait Timeout */

#define SYS_STATUS_LDEERR       0x00040000UL    /* Leading edge detection processing error */

#define SYS_STATUS_reserved     0x00080000UL    /* bit19 reserved */

#define SYS_STATUS_RXOVRR       0x00100000UL    /* Receiver Overrun */

#define SYS_STATUS_RXPTO        0x00200000UL    /* Preamble detection timeout */

#define SYS_STATUS_GPIOIRQ      0x00400000UL    /* GPIO interrupt */

#define SYS_STATUS_SLP2INIT     0x00800000UL    /* SLEEP to INIT */

/*offset 24 */

#define SYS_STATUS_RFPLL_LL     0x01000000UL    /* RF PLL Losing Lock */

#define SYS_STATUS_CLKPLL_LL    0x02000000UL    /* Clock PLL Losing Lock */

#define SYS_STATUS_RXSFDTO      0x04000000UL    /* Receive SFD timeout */

#define SYS_STATUS_HPDWARN      0x08000000UL    /* Half Period Delay Warning */

#define SYS_STATUS_TXBERR       0x10000000UL    /* Transmit Buffer Error */

#define SYS_STATUS_AFFREJ       0x20000000UL    /* Automatic Frame Filtering rejection */

#define SYS_STATUS_HSRBP        0x40000000UL    /* Host Side Receive Buffer Pointer */

#define SYS_STATUS_ICRBP        0x80000000UL    /* IC side Receive Buffer Pointer READ ONLY */

/*offset 32 */

#define SYS_STATUS_RXRSCS       0x0100000000ULL /* Receiver Reed-Solomon Correction Status */

#define SYS_STATUS_RXPREJ       0x0200000000ULL /* Receiver Preamble Rejection */

#define SYS_STATUS_TXPUTE       0x0400000000ULL /* Transmit power up time error */

#define SYS_STATUS_TXERR        (0x0408)        /* These bits are the 16 high bits of status register TXPUTE and HPDWARN flags */

/* All RX events after a correct packet reception mask. */

#define SYS_STATUS_ALL_RX_GOOD (SYS_STATUS_RXDFR | SYS_STATUS_RXFCG | SYS_STATUS_RXPRD | \

                                SYS_STATUS_RXSFDD | SYS_STATUS_RXPHD | SYS_STATUS_LDEDONE)

/* All double buffer events mask. */

#define SYS_STATUS_ALL_DBLBUFF (SYS_STATUS_RXDFR | SYS_STATUS_RXFCG)

/* All RX errors mask. */

#define SYS_STATUS_ALL_RX_ERR  (SYS_STATUS_RXPHE | SYS_STATUS_RXFCE | SYS_STATUS_RXRFSL | SYS_STATUS_RXSFDTO \

                                | SYS_STATUS_AFFREJ | SYS_STATUS_LDEERR)

/* User defined RX timeouts (frame wait timeout and preamble detect timeout) mask. */

#define SYS_STATUS_ALL_RX_TO   (SYS_STATUS_RXRFTO | SYS_STATUS_RXPTO)

/* All TX events mask. */

#define SYS_STATUS_ALL_TX      (SYS_STATUS_AAT | SYS_STATUS_TXFRB | SYS_STATUS_TXPRS | \

                                SYS_STATUS_TXPHS | SYS_STATUS_TXFRS )

/****************************************************************************//**

 * @brief Bit definitions for register RX_FINFO

**/

#define RX_FINFO_ID             0x10            /* RX Frame Information (in double buffer set) */

#define RX_FINFO_OFFSET         0x00

#define RX_FINFO_LEN            (4)

/*mask and shift */

#define RX_FINFO_MASK_32        0xFFFFFBFFUL    /* System event Status Register access mask (all unused fields should always be writen as zero) */

#define RX_FINFO_RXFLEN_MASK    0x0000007FUL    /* Receive Frame Length (0 to 127) */

#define RX_FINFO_RXFLE_MASK     0x00000380UL    /* Receive Frame Length Extension (0 to 7)<<7 */

#define RX_FINFO_RXFL_MASK_1023 0x000003FFUL    /* Receive Frame Length Extension (0 to 1023) */

#define RX_FINFO_RXNSPL_MASK    0x00001800UL    /* Receive Non-Standard Preamble Length */

#define RX_FINFO_RXPSR_MASK     0x000C0000UL    /* RX Preamble Repetition. 00 = 16 symbols, 01 = 64 symbols, 10 = 1024 symbols, 11 = 4096 symbols */

#define RX_FINFO_RXPEL_MASK     0x000C1800UL    /* Receive Preamble Length = RXPSR+RXNSPL */

#define RX_FINFO_RXPEL_64       0x00040000UL    /* Receive Preamble length = 64 */

#define RX_FINFO_RXPEL_128      0x00040800UL    /* Receive Preamble length = 128 */

#define RX_FINFO_RXPEL_256      0x00041000UL    /* Receive Preamble length = 256 */

#define RX_FINFO_RXPEL_512      0x00041800UL    /* Receive Preamble length = 512 */

#define RX_FINFO_RXPEL_1024     0x00080000UL    /* Receive Preamble length = 1024 */

#define RX_FINFO_RXPEL_1536     0x00080800UL    /* Receive Preamble length = 1536 */

#define RX_FINFO_RXPEL_2048     0x00081000UL    /* Receive Preamble length = 2048 */

#define RX_FINFO_RXPEL_4096     0x000C0000UL    /* Receive Preamble length = 4096 */

#define RX_FINFO_RXBR_MASK      0x00006000UL    /* Receive Bit Rate report. This field reports the received bit rate */

#define RX_FINFO_RXBR_110k      0x00000000UL    /* Received bit rate = 110 kbps */

#define RX_FINFO_RXBR_850k      0x00002000UL    /* Received bit rate = 850 kbps */

#define RX_FINFO_RXBR_6M        0x00004000UL    /* Received bit rate = 6.8 Mbps */

#define RX_FINFO_RXBR_SHIFT     (13)

#define RX_FINFO_RNG            0x00008000UL    /* Receiver Ranging. Ranging bit in the received PHY header identifying the frame as a ranging packet. */

#define RX_FINFO_RNG_SHIFT      (15)

#define RX_FINFO_RXPRF_MASK     0x00030000UL    /* RX Pulse Repetition Rate report */

#define RX_FINFO_RXPRF_16M      0x00010000UL    /* PRF being employed in the receiver = 16M */

#define RX_FINFO_RXPRF_64M      0x00020000UL    /* PRF being employed in the receiver = 64M */

#define RX_FINFO_RXPRF_SHIFT    (16)

#define RX_FINFO_RXPACC_MASK    0xFFF00000UL    /* Preamble Accumulation Count */

#define RX_FINFO_RXPACC_SHIFT   (20)

/****************************************************************************//**

 * @brief Bit definitions for register RX_BUFFER

**/

#define RX_BUFFER_ID            0x11            /* Receive Data Buffer (in double buffer set) */

#define RX_BUFFER_LEN           (1024)

/****************************************************************************//**

 * @brief Bit definitions for register RX_FQUAL

**/

#define RX_FQUAL_ID             0x12            /* Rx Frame Quality information (in double buffer set) */

#define RX_FQUAL_LEN            (8)             /* note 64 bit register*/

/*mask and shift */

/*offset 0 */

#define RX_EQUAL_STD_NOISE_MASK 0x0000FFFFULL   /* Standard Deviation of Noise */

#define RX_EQUAL_STD_NOISE_SHIFT (0)

#define STD_NOISE_MASK          RX_EQUAL_STD_NOISE_MASK

#define STD_NOISE_SHIFT         RX_EQUAL_STD_NOISE_SHIFT

/*offset 16 */

#define RX_EQUAL_FP_AMPL2_MASK  0xFFFF0000ULL   /* First Path Amplitude point 2 */

#define RX_EQUAL_FP_AMPL2_SHIFT (16)

#define FP_AMPL2_MASK           RX_EQUAL_FP_AMPL2_MASK

#define FP_AMPL2_SHIFT          RX_EQUAL_FP_AMPL2_SHIFT

/*offset 32*/

#define RX_EQUAL_PP_AMPL3_MASK  0x0000FFFF00000000ULL   /* First Path Amplitude point 3 */

#define RX_EQUAL_PP_AMPL3_SHIFT (32)

#define PP_AMPL3_MASK           RX_EQUAL_PP_AMPL3_MASK

#define PP_AMPL3_SHIFT          RX_EQUAL_PP_AMPL3_SHIFT

/*offset 48*/

#define RX_EQUAL_CIR_MXG_MASK   0xFFFF000000000000ULL   /* Channel Impulse Response Max Growth */

#define RX_EQUAL_CIR_MXG_SHIFT  (48)

#define CIR_MXG_MASK            RX_EQUAL_CIR_MXG_MASK

#define CIR_MXG_SHIFT           RX_EQUAL_CIR_MXG_SHIFT

/****************************************************************************//**

 * @brief Bit definitions for register RX_TTCKI

 *      The value here is the interval over which the timing offset reported

 *      in the RXTOFS field of Register file: 0x14 RX_TTCKO is measured.

 *      The clock offset is calculated by dividing RXTTCKI by RXTOFS.

 *      The value in RXTTCKI will take just one of two values depending on the PRF: 0x01F00000 @ 16 MHz PRF,

 *      and 0x01FC0000 @ 64 MHz PRF.

**/

#define RX_TTCKI_ID             0x13            /* Receiver Time Tracking Interval (in double buffer set) */

#define RX_TTCKI_LEN            (4)

/****************************************************************************//**

 * @brief Bit definitions for register RX_TTCKO

**/

#define RX_TTCKO_ID             0x14            /* Receiver Time Tracking Offset (in double buffer set) */

#define RX_TTCKO_LEN            (5)             /* Note 40 bit register */

/*mask and shift */

#define RX_TTCKO_MASK_32        0xFF07FFFFUL    /* Receiver Time Tracking Offset access mask (all unused fields should always be writen as zero) */

/*offset 0 */

#define RX_TTCKO_RXTOFS_MASK    0x0007FFFFUL    /* RX time tracking offset. This RXTOFS value is a 19-bit signed quantity*/

/*offset 24 */

#define RX_TTCKO_RSMPDEL_MASK   0xFF000000UL    /* This 8-bit field reports an internal re-sampler delay value */

/*offset 32 */

#define RX_TTCKO_RCPHASE_MASK   0x7F0000000000ULL   /* This 7-bit field reports the receive carrier phase adjustment at time the ranging timestamp is made. */

/****************************************************************************//**

 * @brief Bit definitions for register RX_TIME

**/

#define RX_TIME_ID              0x15            /* Receive Message Time of Arrival (in double buffer set) */

#define RX_TIME_LLEN            (14)

#define RX_TIME_RX_STAMP_LEN    (5)             /* read only 5 bytes (the adjusted timestamp (40:0)) */

#define RX_STAMP_LEN            RX_TIME_RX_STAMP_LEN

/*mask and shift */

#define RX_TIME_RX_STAMP_OFFSET  (0) /* byte 0..4 40 bit Reports the fully adjusted time of reception. */

#define RX_TIME_FP_INDEX_OFFSET  (5)    /* byte 5..6 16 bit First path index. */

#define RX_TIME_FP_AMPL1_OFFSET  (7)    /* byte 7..8 16 bit First Path Amplitude point 1 */   /* doc bug */

#define RX_TIME_FP_RAWST_OFFSET  (9)    /* byte 9..13 40 bit Raw Timestamp for the frame */

/****************************************************************************//**

 * @brief Bit definitions for register

**/

#define REG_16_ID_RESERVED      0x16

/****************************************************************************//**

 * @brief Bit definitions for register

**/

#define TX_TIME_ID              0x17            /* Transmit Message Time of Sending */

#define TX_TIME_LLEN            (10)

#define TX_TIME_TX_STAMP_LEN    (5)             /* 40-bits = 5 bytes */

#define TX_STAMP_LEN            TX_TIME_TX_STAMP_LEN

/*mask and shift */

#define TX_TIME_TX_STAMP_OFFSET  (0) /* byte 0..4 40 bit Reports the fully adjusted time of transmission */

#define TX_TIME_TX_RAWST_OFFSET  (5) /* byte 5..9 40 bit Raw Timestamp for the frame */

/****************************************************************************//**

 * @brief Bit definitions for register TX_ANTD

**/

#define TX_ANTD_ID              0x18            /* 16-bit Delay from Transmit to Antenna */

#define TX_ANTD_OFFSET          0x00

#define TX_ANTD_LEN             (2)

/****************************************************************************//**

 * @brief Bit definitions for register SYS_STATES

 *        Register map register file 0x19 is reserved

 *

**/

#define SYS_STATE_ID            0x19            /* System State information READ ONLY */

#define SYS_STATE_LEN           (5)

/****************************************************************************//**

 * @brief Bit definitions for register ACK_RESP_T

**/

/* Acknowledge (31:24 preamble symbol delay before auto ACK is sent) and respose (19:0 - unit 1us) timer */

#define ACK_RESP_T_ID           0x1A            /* Acknowledgement Time and Response Time */

#define ACK_RESP_T_LEN          (4)

/*mask and shift */

#define ACK_RESP_T_MASK         0xFF0FFFFFUL    /* Acknowledgement Time and Response access mask */

#define ACK_RESP_T_W4R_TIM_OFFSET 0             /* In bytes */

#define ACK_RESP_T_W4R_TIM_MASK 0x000FFFFFUL    /* Wait-for-Response turn-around Time 20 bit field */

#define W4R_TIM_MASK            ACK_RESP_T_W4R_TIM_MASK

#define ACK_RESP_T_ACK_TIM_OFFSET 3             /* In bytes */

#define ACK_RESP_T_ACK_TIM_MASK 0xFF000000UL    /* Auto-Acknowledgement turn-around Time */

#define ACK_TIM_MASK            ACK_RESP_T_ACK_TIM_MASK

/****************************************************************************//**

 * @brief Bit definitions for register 0x1B 0x1C

**/

#define REG_1B_ID_RESERVED      0x1B

#define REG_1C_ID_RESERVED      0x1C

/****************************************************************************//**

 * @brief Bit definitions for register RX_SNIFF

 *        Sniff Mode Configuration or Pulsed Preamble Reception Configuration

**/

#define RX_SNIFF_ID             0x1D            /* Sniff Mode Configuration */

#define RX_SNIFF_OFFSET         0x00

#define RX_SNIFF_LEN            (4)

/*mask and shift */

#define RX_SNIFF_MASK           0x0000FF0FUL    /*  */

#define RX_SNIFF_SNIFF_ONT_MASK 0x0000000FUL    /* SNIFF Mode ON time. Specified in units of PAC */

#define SNIFF_ONT_MASK          RX_SNIFF_SNIFF_ONT_MASK

#define RX_SNIFF_SNIFF_OFFT_MASK 0x0000FF00UL   /* SNIFF Mode OFF time specified in units of approximately 1mkS, or 128 system clock cycles.*/

#define SNIFF_OFFT_MASK         RX_SNIFF_SNIFF_OFFT_MASK

/****************************************************************************//**

 * @brief Bit definitions for register TX_POWER

**/

#define TX_POWER_ID             0x1E            /* TX Power Control */

#define TX_POWER_LEN            (4)

/*mask and shift definition for Smart Transmit Power Control*/

#define TX_POWER_BOOSTNORM_MASK 0x00000000UL    /* This is the normal power setting used for frames that do not fall */

#define BOOSTNORM_MASK          TX_POWER_BOOSTNORM_MASK

#define TX_POWER_BOOSTNORM_SHIFT (0)

#define TX_POWER_BOOSTP500_MASK 0x00000000UL    /* This value sets the power applied during transmission at the 6.8 Mbps data rate frames that are less than 0.5 ms duration */

#define BOOSTP500_MASK          TX_POWER_BOOSTP500_MASK

#define TX_POWER_BOOSTP500_SHIFT (8)

#define TX_POWER_BOOSTP250_MASK 0x00000000UL    /* This value sets the power applied during transmission at the 6.8 Mbps data rate frames that are less than 0.25 ms duration */

#define BOOSTP250_MASK          TX_POWER_BOOSTP250_MASK

#define TX_POWER_BOOSTP250_SHIFT (16)

#define TX_POWER_BOOSTP125_MASK 0x00000000UL    /* This value sets the power applied during transmission at the 6.8 Mbps data rate frames that are less than 0.125 ms */

#define BOOSTP125_MASK          TX_POWER_BOOSTP125_MASK

#define TX_POWER_BOOSTP125_SHIFT (24)

/*mask and shift definition for Manual Transmit Power Control (DIS_STXP=1 in SYS_CFG)*/

#define TX_POWER_MAN_DEFAULT    0x0E080222UL

#define TX_POWER_TXPOWPHR_MASK  0x0000FF00UL    /* This power setting is applied during the transmission of the PHY header (PHR) portion of the frame. */

#define TX_POWER_TXPOWSD_MASK   0x00FF0000UL    /* This power setting is applied during the transmission of the synchronisation header (SHR) and data portions of the frame. */

/****************************************************************************//**

 * @brief Bit definitions for register CHAN_CTRL

**/

#define CHAN_CTRL_ID            0x1F            /* Channel Control */

#define CHAN_CTRL_LEN           (4)

/*mask and shift */

#define CHAN_CTRL_MASK          0xFFFF00FFUL    /* Channel Control Register access mask */

#define CHAN_CTRL_TX_CHAN_MASK  0x0000000FUL    /* Supported channels are 1, 2, 3, 4, 5, and 7.*/

#define CHAN_CTRL_TX_CHAN_SHIFT (0)             /* Bits 0..3        TX channel number 0-15 selection */

#define CHAN_CTRL_RX_CHAN_MASK  0x000000F0UL

#define CHAN_CTRL_RX_CHAN_SHIFT (4)             /* Bits 4..7        RX channel number 0-15 selection */

#define CHAN_CTRL_RXFPRF_MASK   0x000C0000UL    /* Bits 18..19      Specify (Force) RX Pulse Repetition Rate: 00 = 4 MHz, 01 = 16 MHz, 10 = 64MHz. */

#define CHAN_CTRL_RXFPRF_SHIFT  (18)

/* Specific RXFPRF configuration */

#define CHAN_CTRL_RXFPRF_4      0x00000000UL    /* Specify (Force) RX Pulse Repetition Rate: 00 = 4 MHz, 01 = 16 MHz, 10 = 64MHz. */

#define CHAN_CTRL_RXFPRF_16     0x00040000UL    /* Specify (Force) RX Pulse Repetition Rate: 00 = 4 MHz, 01 = 16 MHz, 10 = 64MHz. */

#define CHAN_CTRL_RXFPRF_64     0x00080000UL    /* Specify (Force) RX Pulse Repetition Rate: 00 = 4 MHz, 01 = 16 MHz, 10 = 64MHz. */

#define CHAN_CTRL_TX_PCOD_MASK  0x07C00000UL    /* Bits 22..26      TX Preamble Code selection, 1 to 24. */

#define CHAN_CTRL_TX_PCOD_SHIFT (22)

#define CHAN_CTRL_RX_PCOD_MASK  0xF8000000UL    /* Bits 27..31      RX Preamble Code selection, 1 to 24. */

#define CHAN_CTRL_RX_PCOD_SHIFT (27)

/*offset 16 */

#define CHAN_CTRL_DWSFD         0x00020000UL    /* Bit 17 This bit enables a non-standard DecaWave proprietary SFD sequence. */

#define CHAN_CTRL_DWSFD_SHIFT   (17)

#define CHAN_CTRL_TNSSFD        0x00100000UL    /* Bit 20 Non-standard SFD in the transmitter */

#define CHAN_CTRL_TNSSFD_SHIFT  (20)

#define CHAN_CTRL_RNSSFD        0x00200000UL    /* Bit 21 Non-standard SFD in the receiver */

#define CHAN_CTRL_RNSSFD_SHIFT  (21)

/****************************************************************************//**

 * @brief Bit definitions for register 0x20

**/

#define REG_20_ID_RESERVED      0x20

/****************************************************************************//**

 * @brief Bit definitions for register USR_SFD

 *        Please read User Manual : User defined SFD sequence

**/

#define USR_SFD_ID              0x21            /* User-specified short/long TX/RX SFD sequences */

#define USR_SFD_LEN             (41)

#define DW_NS_SFD_LEN_110K      64              /* Decawave non-standard SFD length for 110 kbps */

#define DW_NS_SFD_LEN_850K      16              /* Decawave non-standard SFD length for 850 kbps */

#define DW_NS_SFD_LEN_6M8       8               /* Decawave non-standard SFD length for 6.8 Mbps */

/****************************************************************************//**

 * @brief Bit definitions for register

**/

#define REG_22_ID_RESERVED      0x22

/****************************************************************************//**

 * @brief Bit definitions for register AGC_CTRL

 * Please take care to write to this register as doing so may cause the DW1000 to malfunction

**/

#define AGC_CTRL_ID             0x23            /* Automatic Gain Control configuration */

#define AGC_CTRL_LEN            (32)

#define AGC_CFG_STS_ID          AGC_CTRL_ID

/* offset from AGC_CTRL_ID in bytes */

#define AGC_CTRL1_OFFSET        (0x02)

#define AGC_CTRL1_LEN           (2)

#define AGC_CTRL1_MASK          0x0001          /* access mask to AGC configuration and control register */

#define AGC_CTRL1_DIS_AM        0x0001          /* Disable AGC Measurement. The DIS_AM bit is set by default. */

/* offset from AGC_CTRL_ID in bytes */

/* Please take care not to write other values to this register as doing so may cause the DW1000 to malfunction */

#define AGC_TUNE1_OFFSET        (0x04)

#define AGC_TUNE1_LEN           (2)

#define AGC_TUNE1_MASK          0xFFFF          /* It is a 16-bit tuning register for the AGC. */

#define AGC_TUNE1_16M           0x8870

#define AGC_TUNE1_64M           0x889B

/* offset from AGC_CTRL_ID in bytes */

/* Please take care not to write other values to this register as doing so may cause the DW1000 to malfunction */

#define AGC_TUNE2_OFFSET        (0x0C)

#define AGC_TUNE2_LEN           (4)

#define AGC_TUNE2_MASK          0xFFFFFFFFUL

#define AGC_TUNE2_VAL           0X2502A907UL

/* offset from AGC_CTRL_ID in bytes */

/* Please take care not to write other values to this register as doing so may cause the DW1000 to malfunction */

#define AGC_TUNE3_OFFSET        (0x12)

#define AGC_TUNE3_LEN           (2)

#define AGC_TUNE3_MASK          0xFFFF

#define AGC_TUNE3_VAL           0X0055

/* offset from AGC_CTRL_ID in bytes */

#define AGC_STAT1_OFFSET        (0x1E)

#define AGC_STAT1_LEN           (3)

#define AGC_STAT1_MASK          0x0FFFFF

#define AGC_STAT1_EDG1_MASK     0x0007C0        /* This 5-bit gain value relates to input noise power measurement. */

#define AGC_STAT1_EDG2_MASK     0x0FF800        /* This 9-bit value relates to the input noise power measurement. */

/****************************************************************************//**

 * @brief Bit definitions for register EXT_SYNC

**/

#define EXT_SYNC_ID             0x24            /* External synchronisation control */

#define EXT_SYNC_LEN            (12)

/* offset from EXT_SYNC_ID in bytes */

#define EC_CTRL_OFFSET          (0x00)

#define EC_CTRL_LEN             (4)

#define EC_CTRL_MASK            0x00000FFBUL    /* sub-register 0x00 is the External clock synchronisation counter configuration register */

#define EC_CTRL_OSTSM           0x00000001UL    /* External transmit synchronisation mode enable */

#define EC_CTRL_OSRSM           0x00000002UL    /* External receive synchronisation mode enable */

#define EC_CTRL_PLLLCK          0x04            /* PLL lock detect enable */

#define EC_CTRL_OSTRM           0x00000800UL    /* External timebase reset mode enable */

#define EC_CTRL_WAIT_MASK       0x000007F8UL    /* Wait counter used for external transmit synchronisation and external timebase reset */

/* offset from EXT_SYNC_ID in bytes */

#define EC_RXTC_OFFSET          (0x04)

#define EC_RXTC_LEN             (4)

#define EC_RXTC_MASK            0xFFFFFFFFUL    /* External clock synchronisation counter captured on RMARKER */

/* offset from EXT_SYNC_ID in bytes */

#define EC_GOLP                 (0x08)

#define EC_GOLP_LEN             (4)

#define EC_GOLP_MASK            0x0000003FUL    /* sub-register 0x08 is the External clock offset to first path 1 GHz counter, EC_GOLP */

#define EC_GOLP_OFFSET_EXT_MASK 0x0000003FUL    /* This register contains the 1 GHz count from the arrival of the RMARKER and the next edge of the external clock. */

/****************************************************************************//**

 * @brief Bit definitions for register ACC_MEM

**/

#define ACC_MEM_ID              0x25            /* Read access to accumulator data */

#define ACC_MEM_LEN             (4064)

/****************************************************************************//**

 * @brief Bit definitions for register GPIO_CTRL

**/

#define GPIO_CTRL_ID            0x26            /* Peripheral register bus 1 access - GPIO control */

#define GPIO_CTRL_LEN           (44)

/* offset from GPIO_CTRL in bytes */

#define GPIO_MODE_OFFSET        0x00            /* sub-register 0x00 is the GPIO Mode Control Register */

#define GPIO_MODE_LEN           (4)

#define GPIO_MODE_MASK          0x00FFFFC0UL

#define GPIO_MSGP0_MASK         0x000000C0UL    /* Mode Selection for GPIO0/RXOKLED */

#define GPIO_MSGP1_MASK         0x00000300UL    /* Mode Selection for GPIO1/SFDLED */

#define GPIO_MSGP2_MASK         0x00000C00UL    /* Mode Selection for GPIO2/RXLED */

#define GPIO_MSGP3_MASK         0x00003000UL    /* Mode Selection for GPIO3/TXLED */

#define GPIO_MSGP4_MASK         0x0000C000UL    /* Mode Selection for GPIO4/EXTPA */

#define GPIO_MSGP5_MASK         0x00030000UL    /* Mode Selection for GPIO5/EXTTXE */

#define GPIO_MSGP6_MASK         0x000C0000UL    /* Mode Selection for GPIO6/EXTRXE */

#define GPIO_MSGP7_MASK         0x00300000UL    /* Mode Selection for SYNC/GPIO7 */

#define GPIO_MSGP8_MASK         0x00C00000UL    /* Mode Selection for IRQ/GPIO8 */

#define GPIO_PIN2_RXLED         0x00000400UL    /* The pin operates as the RXLED output */

#define GPIO_PIN3_TXLED         0x00001000UL    /* The pin operates as the TXLED output */

#define GPIO_PIN4_EXTPA         0x00004000UL    /* The pin operates as the EXTPA output */

#define GPIO_PIN5_EXTTXE        0x00010000UL    /* The pin operates as the EXTTXE output */

#define GPIO_PIN6_EXTRXE        0x00040000UL    /* The pin operates as the EXTRXE output */

/* offset from GPIO_CTRL in bytes */

#define GPIO_DIR_OFFSET         0x08            /* sub-register 0x08 is the GPIO Direction Control Register */

#define GPIO_DIR_LEN            (3)

#define GPIO_DIR_MASK           0x0011FFFFUL

#define GxP0                    0x00000001UL    /* GPIO0 Only changed if the GxM0 mask bit has a value of 1 for the write operation*/

#define GxP1                    0x00000002UL    /* GPIO1. (See GDP0). */

#define GxP2                    0x00000004UL    /* GPIO2. (See GDP0). */

#define GxP3                    0x00000008UL    /* GPIO3. (See GDP0). */

#define GxP4                    0x00000100UL    /* GPIO4. (See GDP0). */

#define GxP5                    0x00000200UL    /* GPIO5. (See GDP0). */

#define GxP6                    0x00000400UL    /* GPIO6. (See GDP0). */

#define GxP7                    0x00000800UL    /* GPIO7. (See GDP0). */

#define GxP8                    0x00010000UL    /* GPIO8 */

#define GxM0                    0x00000010UL    /* Mask for GPIO0 */

#define GxM1                    0x00000020UL    /* Mask for GPIO1. (See GDM0). */

#define GxM2                    0x00000040UL    /* Mask for GPIO2. (See GDM0). */

#define GxM3                    0x00000080UL    /* Mask for GPIO3. (See GDM0). */

#define GxM4                    0x00001000UL    /* Mask for GPIO4. (See GDM0). */

#define GxM5                    0x00002000UL    /* Mask for GPIO5. (See GDM0). */

#define GxM6                    0x00004000UL    /* Mask for GPIO6. (See GDM0). */

#define GxM7                    0x00008000UL    /* Mask for GPIO7. (See GDM0). */

#define GxM8                    0x00100000UL    /* Mask for GPIO8. (See GDM0). */

#define GDP0    GxP0    /* Direction Selection for GPIO0. 1 = input, 0 = output. Only changed if the GDM0 mask bit has a value of 1 for the write operation*/

#define GDP1    GxP1    /* Direction Selection for GPIO1. (See GDP0). */

#define GDP2    GxP2    /* Direction Selection for GPIO2. (See GDP0). */

#define GDP3    GxP3    /* Direction Selection for GPIO3. (See GDP0). */

#define GDP4    GxP4    /* Direction Selection for GPIO4. (See GDP0). */

#define GDP5    GxP5    /* Direction Selection for GPIO5. (See GDP0). */

#define GDP6    GxP6    /* Direction Selection for GPIO6. (See GDP0). */

#define GDP7    GxP7    /* Direction Selection for GPIO7. (See GDP0). */

#define GDP8    GxP8    /* Direction Selection for GPIO8 */

#define GDM0    GxM0    /* Mask for setting the direction of GPIO0 */

#define GDM1    GxM1    /* Mask for setting the direction of GPIO1. (See GDM0). */

#define GDM2    GxM2    /* Mask for setting the direction of GPIO2. (See GDM0). */

#define GDM3    GxM3    /* Mask for setting the direction of GPIO3. (See GDM0). */

#define GDM4    GxM4    /* Mask for setting the direction of GPIO4. (See GDM0). */

#define GDM5    GxM5    /* Mask for setting the direction of GPIO5. (See GDM0). */

#define GDM6    GxM6    /* Mask for setting the direction of GPIO6. (See GDM0). */

#define GDM7    GxM7    /* Mask for setting the direction of GPIO7. (See GDM0). */

#define GDM8    GxM8    /* Mask for setting the direction of GPIO8. (See GDM0). */

/* offset from GPIO_CTRL in bytes */

#define GPIO_DOUT_OFFSET        0x0C            /* sub-register 0x0C is the GPIO data output register. */

#define GPIO_DOUT_LEN           (3)

#define GPIO_DOUT_MASK          GPIO_DIR_MASK

/* offset from GPIO_CTRL in bytes */

#define GPIO_IRQE_OFFSET        0x10            /* sub-register 0x10 is the GPIO interrupt enable register */

#define GPIO_IRQE_LEN           (4)

#define GPIO_IRQE_MASK          0x000001FFUL

#define GIRQx0                  0x00000001UL    /* IRQ bit0 */

#define GIRQx1                  0x00000002UL    /* IRQ bit1 */

#define GIRQx2                  0x00000004UL    /* IRQ bit2 */

#define GIRQx3                  0x00000008UL    /* IRQ bit3 */

#define GIRQx4                  0x00000010UL    /* IRQ bit4 */

#define GIRQx5                  0x00000020UL    /* IRQ bit5 */

#define GIRQx6                  0x00000040UL    /* IRQ bit6 */

#define GIRQx7                  0x00000080UL    /* IRQ bit7 */

#define GIRQx8                  0x00000100UL    /* IRQ bit8 */

#define GIRQE0  GIRQx0  /* GPIO IRQ Enable for GPIO0 input. Value 1 = enable, 0 = disable*/

#define GIRQE1  GIRQx1  /*  */

#define GIRQE2  GIRQx2  /*  */

#define GIRQE3  GIRQx3  /*  */

#define GIRQE4  GIRQx4  /*  */

#define GIRQE5  GIRQx5  /*  */

#define GIRQE6  GIRQx6  /*  */

#define GIRQE7  GIRQx7  /*  */

#define GIRQE8  GIRQx8  /* Value 1 = enable, 0 = disable */

/* offset from GPIO_CTRL in bytes */

#define GPIO_ISEN_OFFSET        0x14    /* sub-register 0x14 is the GPIO interrupt sense selection register */

#define GPIO_ISEN_LEN           (4)

#define GPIO_ISEN_MASK          GPIO_IRQE_MASK

#define GISEN0  GIRQx0  /* GPIO IRQ Sense selection GPIO0 input. Value 0 = High or Rising-Edge, 1 = Low or falling-edge.*/

#define GISEN1  GIRQx1  /*  */

#define GISEN2  GIRQx2  /*  */

#define GISEN3  GIRQx3  /*  */

#define GISEN4  GIRQx4  /*  */

#define GISEN5  GIRQx5  /*  */

#define GISEN6  GIRQx6  /*  */

#define GISEN7  GIRQx7  /*  */

#define GISEN8  GIRQx8  /* Value 0 = High or Rising-Edge, 1 = Low or falling-edge */

/* offset from GPIO_CTRL in bytes */

#define GPIO_IMODE_OFFSET       0x18    /* sub-register 0x18 is the GPIO interrupt mode selection register */

#define GPIO_IMODE_LEN          (4)

#define GPIO_IMODE_MASK         GPIO_IRQE_MASK

#define GIMOD0  GIRQx0  /* GPIO IRQ Mode selection for GPIO0 input. Value 0 = Level sensitive interrupt. Value 1 = Edge triggered interrupt */

#define GIMOD1  GIRQx1  /*  */

#define GIMOD2  GIRQx2  /*  */

#define GIMOD3  GIRQx3  /*  */

#define GIMOD4  GIRQx4  /*  */

#define GIMOD5  GIRQx5  /*  */

#define GIMOD6  GIRQx6  /*  */

#define GIMOD7  GIRQx7  /*  */

#define GIMOD8  GIRQx8  /* Value 0 = Level, 1 = Edge. */

/* offset from EXT_SYNC_ID in bytes */

#define GPIO_IBES_OFFSET        0x1C    /* sub-register 0x1C is the GPIO interrupt Both Edge selection register */

#define GPIO_IBES_LEN           (4)

#define GPIO_IBES_MASK          GPIO_IRQE_MASK  /*  */

#define GIBES0  GIRQx0  /* GPIO IRQ Both Edge selection for GPIO0 input. Value 0 = GPIO_IMODE register selects the edge. Value 1 = Both edges trigger the interrupt. */

#define GIBES1  GIRQx1  /*  */

#define GIBES2  GIRQx2  /*  */

#define GIBES3  GIRQx3  /*  */

#define GIBES4  GIRQx4  /*  */

#define GIBES5  GIRQx5  /*  */

#define GIBES6  GIRQx6  /*  */

#define GIBES7  GIRQx7  /*  */

#define GIBES8  GIRQx8  /* Value 0 = use GPIO_IMODE, 1 = Both Edges */

/* offset from GPIO_CTRL in bytes */

#define GPIO_ICLR_OFFSET        0x20    /* sub-register 0x20 is the GPIO interrupt clear register */

#define GPIO_ICLR_LEN           (4)

#define GPIO_ICLR_MASK          GPIO_IRQE_MASK  /*  */

#define GICLR0  GIRQx0  /* GPIO IRQ latch clear for GPIO0 input. Write 1 to clear the GPIO0 interrupt latch. Writing 0 has no effect. Reading returns zero */

#define GICLR1  GIRQx1  /*  */

#define GICLR2  GIRQx2  /*  */

#define GICLR3  GIRQx3  /*  */

#define GICLR4  GIRQx4  /*  */

#define GICLR5  GIRQx5  /*  */

#define GICLR6  GIRQx6  /*  */

#define GICLR7  GIRQx7  /*  */

#define GICLR8  GIRQx8  /* Write 1 to clear the interrupt latch */

/* offset from GPIO_CTRL in bytes */

#define GPIO_IDBE_OFFSET        0x24    /* sub-register 0x24 is the GPIO interrupt de-bounce enable register */

#define GPIO_IDBE_LEN           (4)

#define GPIO_IDBE_MASK          GPIO_IRQE_MASK

#define GIDBE0  GIRQx0  /* GPIO IRQ de-bounce enable for GPIO0. Value 1 = de-bounce enabled. Value 0 = de-bounce disabled */

#define GIDBE1  GIRQx1  /*  */

#define GIDBE2  GIRQx2  /*  */

#define GIDBE3  GIRQx3  /*  */

#define GIDBE4  GIRQx4  /*  */

#define GIDBE5  GIRQx5  /*  */

#define GIDBE6  GIRQx6  /*  */

#define GIDBE7  GIRQx7  /*  */

#define GIDBE8  GIRQx8  /* Value 1 = de-bounce enabled, 0 = de-bounce disabled */

/* offset from GPIO_CTRL in bytes */

#define GPIO_RAW_OFFSET         0x28    /* sub-register 0x28 allows the raw state of the GPIO pin to be read. */

#define GPIO_RAW_LEN            (4)

#define GPIO_RAW_MASK           GPIO_IRQE_MASK

#define GRAWP0  GIRQx0  /* This bit reflects the raw state of GPIO0 */

#define GRAWP1  GIRQx1  /*  */

#define GRAWP2  GIRQx2  /*  */

#define GRAWP3  GIRQx3  /*  */

#define GRAWP4  GIRQx4  /*  */

#define GRAWP5  GIRQx5  /*  */

#define GRAWP6  GIRQx6  /*  */

#define GRAWP7  GIRQx7  /*  */

#define GRAWP8  GIRQx8  /* This bit reflects the raw state of GPIO8 */

/****************************************************************************//**

 * @brief Bit definitions for register  DRX_CONF

 * Digital Receiver configuration block

**/

#define DRX_CONF_ID             0x27            /* Digital Receiver configuration */

#define DRX_CONF_LEN            (44)

/* offset from DRX_CONF_ID in bytes */

#define DRX_TUNE0b_OFFSET       (0x02)  /* sub-register 0x02 is a 16-bit tuning register. */

#define DRX_TUNE0b_LEN          (2)

#define DRX_TUNE0b_MASK         0xFFFF  /* 7.2.40.2 Sub-Register 0x27:02  DRX_TUNE0b */

#define DRX_TUNE0b_110K_STD     0x000A

#define DRX_TUNE0b_110K_NSTD    0x0016

#define DRX_TUNE0b_850K_STD     0x0001

#define DRX_TUNE0b_850K_NSTD    0x0006

#define DRX_TUNE0b_6M8_STD      0x0001

#define DRX_TUNE0b_6M8_NSTD     0x0002

/* offset from DRX_CONF_ID in bytes */

#define DRX_TUNE1a_OFFSET       0x04    /* 7.2.40.3 Sub-Register 0x27:04  DRX_TUNE1a */

#define DRX_TUNE1a_LEN          (2)

#define DRX_TUNE1a_MASK         0xFFFF

#define DRX_TUNE1a_PRF16        0x0087

#define DRX_TUNE1a_PRF64        0x008D

/* offset from DRX_CONF_ID in bytes */

#define DRX_TUNE1b_OFFSET       0x06    /* 7.2.40.4 Sub-Register 0x27:06  DRX_TUNE1b */

#define DRX_TUNE1b_LEN          (2)

#define DRX_TUNE1b_MASK         0xFFFF

#define DRX_TUNE1b_110K         0x0064

#define DRX_TUNE1b_850K_6M8     0x0020

#define DRX_TUNE1b_6M8_PRE64    0x0010

/* offset from DRX_CONF_ID in bytes */

#define DRX_TUNE2_OFFSET        0x08    /* 7.2.40.5 Sub-Register 0x27:08  DRX_TUNE2 */

#define DRX_TUNE2_LEN           (4)

#define DRX_TUNE2_MASK          0xFFFFFFFFUL

#define DRX_TUNE2_PRF16_PAC8    0x311A002DUL

#define DRX_TUNE2_PRF16_PAC16   0x331A0052UL

#define DRX_TUNE2_PRF16_PAC32   0x351A009AUL

#define DRX_TUNE2_PRF16_PAC64   0x371A011DUL

#define DRX_TUNE2_PRF64_PAC8    0x313B006BUL

#define DRX_TUNE2_PRF64_PAC16   0x333B00BEUL

#define DRX_TUNE2_PRF64_PAC32   0x353B015EUL

#define DRX_TUNE2_PRF64_PAC64   0x373B0296UL

/* offset from DRX_CONF_ID in bytes */

/* WARNING: Please do NOT set DRX_SFDTOC to zero (disabling SFD detection timeout)

 * since this risks IC malfunction due to prolonged receiver activity in the event of false preamble detection.

 */